move time zone selection to config.rs

src/config.rs

@@ -10,7 +10,7 @@ pub(crate) const T_ON: &'static str = "17:00";
 pub(crate) const T_OFF: &'static str = "09:00";
 
 /// Time zone for T_ON and T_OFF.
-pub(crate) const TZ: chrono::TimeZone = chrono_tz::US::Pacific;
+pub(crate) const TZ: chrono_tz::Tz = chrono_tz::US::Pacific;
 
 /// Access point SSID.
 pub(crate) const WIFI_SSID: &'static str = "Example";

src/main.rs

@@ -4,7 +4,11 @@ use anyhow::{bail, Result};
 use chrono::{NaiveTime, Utc};
 use esp_idf_svc::{
     eventloop::EspSystemEventLoop,
-    hal::{delay::FreeRtos, gpio::*, prelude::Peripherals},
+    hal::{
+        delay::FreeRtos,
+        gpio::{self, Gpio7, OutputPin, PinDriver},
+        prelude::Peripherals,
+    },
     sntp::{EspSntp, SntpConf, SyncMode},
     wifi::EspWifi,
 };
@@ -18,15 +22,15 @@ mod wifi;
 const CONTROL_LOOP_INTVL: u32 = 60000;
 
 /// Struct holding resources which should remain in scope throughout execution.
-struct AppState {
+struct AppState<P: OutputPin> {
     ntp: EspSntp<'static>,
-    switch_driver: PinDriver<'static>,
+    switch_driver: PinDriver<'static, P, gpio::Output>,
     wifi: EspWifi<'static>,
 }
 
 fn main() -> Result<()> {
-    let AppState {
+    let AppState::<_> {
-        ntp: mut_ntp,
+        ntp: _ntp,
         mut switch_driver,
         wifi: _wifi,
     } = setup()?;
@@ -71,7 +75,7 @@ fn main() -> Result<()> {
 /// Runs initial application startup tasks, including connecting WiFi, syncing
 /// system time over SNTP, and setting the initial switch state. May block for
 /// several seconds, or indefinitely if initial SNTP sync is not successful.
-fn setup() -> Result<Box<AppState>> {
+fn setup() -> Result<Box<AppState<Gpio7>>> {
     // It is necessary to call this function once. Otherwise some patches to
     // the runtime implemented by esp-idf-sys might not link properly. Refer
     // to https://github.com/esp-rs/esp-idf-template/issues/71.
@@ -83,7 +87,7 @@ fn setup() -> Result<Box<AppState>> {
     let peripherals = Peripherals::take()?;
     let sysloop = EspSystemEventLoop::take()?;
 
-    let mut switch_driver = PinDriver::output(app_state.peripherals.pins.gpio7)?;
+    let mut switch_driver = PinDriver::output(peripherals.pins.gpio7)?;
     switch_driver.set_low()?;
 
     // Dropping EspWifi shuts down the connection, so this variable must remain
@@ -99,9 +103,9 @@ fn setup() -> Result<Box<AppState>> {
     })?;
     crate::ntp::wait_for_sync(&ntp);
 
-    Ok(Box::new(AppState {
+    Ok(Box::new(AppState::<_> {
         ntp,
         switch_driver,
-        wifi,
+        wifi: *wifi,
     }))
 }

src/ntp.rs

@@ -1,4 +1,7 @@
-use esp_idf_svc::sntp::{EspSntp, SyncStatus};
+use esp_idf_svc::{
+    hal::delay::FreRtos,
+    sntp::{EspSntp, SyncStatus},
+};
 use log::info;
 
 /// Delay between checks of the initial NTP sync check, in milliseconds.
@@ -10,8 +13,8 @@ const SNTP_STATUS_POLL_INTVL: u32 = 2000;
 /// this function twice will cause the second invocation to wait for the next
 /// synchronization event.
 pub(crate) fn wait_for_sync(client: &EspSntp) {
-    while ntp.get_sync_status() != SyncStatus::Completed {
+    while client.get_sync_status() != SyncStatus::Completed {
         info!("Waiting for SNTP to sync...");
-        FreeRtos::delay_ms(SNTP_STATUS_POLL_INTVL_MS);
+        FreeRtos::delay_ms(SNTP_STATUS_POLL_INTVL);
     }
 }